Moodie Outdoor Products supported the installation of two FRP Golf Course Bridges at Ryde-Parramatta Golf Course, NSW.
The project involved design, fabrication & delivery of two FRP Golf Course bridges. Bridge dimensions were 14.5m x 2m and 15.5m x 2m clear width, with complete FRP structure, truss handrails, and FRP mini mesh decking. The bridges were designed to support golf karts and maintenance buggies.
To find out more about this project please do not hesitate to Contact Us today.
Moodie Outdoor Products supported the installation of two FRP Golf Course Swale Bridges at Cumberland Golf Course, NSW.
The project involved design, fabrication & delivery of two FRP Golf Course bridges. Bridge dimensions were 4m x 1.8m and 4m x 1m clear width, with complete FRP structure, side kick boards, and FRP mini mesh decking. The bridges were designed to support golf karts and maintenance buggies.
To find out more about this project please do not hesitate to Contact Us today.
Moodie Outdoor Products has recently completed the supply and installation of a fully enclosed FRP (Fibreglass Reinforced Polymer) pedestrian bridge in Erina, NSW. The single span bridge is 9m long, 2m wide, 2.5m high enclosed roof, and engineered to 4kPa.
The specification for a fully enclosed FRP bridge was to enable secure access between the shopping centre tenant and an adjacent outdoor structure. SecureMax mesh panels were installed for enhanced security of retail goods whilst traversing the bridge.
Read our blog article about the benefits of using FRP materials.
Contact us to discuss your next custom pedestrian bridge project using FRP or steel materials.
Moodie Outdoor Products has recently completed the supply and installation of an FRP (Fibreglass Reinforced Polymer) pedestrian bridge in Erina, NSW. The single span bridge is 9m long with 2.5m clear width between handrails, and engineered to 4kPa.
The bridge was assembled on site from a flat-pack, and then craned into position. SecureMax mesh panels were installed for maximum protection of pedestrians.
Read our blog article about the benefits of using FRP materials.
Contact us to discuss your next custom pedestrian bridge project using FRP or steel materials.
Moodie Outdoor Products has recently completed the supply and installation of a Riesling steel bridge in Nambour, Qld.
The single span bridge is 18m long with 1.5m clear width between handrails to facilitate a creek crossing for pedestrians. The bridge is designed to 5kPa pedestrian loading with HDG (hot-dip galvanised) steel balustrade panels, cycle rails, and FRP mini-mesh decking.
Manufactured and factory assembled by Outside Products, the bridge was transported to site by two semi-trailers, and craned into position through heavy tree coverage.
Contact us to discuss your next custom pedestrian bridge project.
Moodie Outdoor Products has recently completed the supply and installation of a Riesling steel bridge in Grafton, NSW.
The single span bridge is 26m long with 2.5m clear width between handrails to facilitate a shared pathway for pedestrians and bicycles. The bridge is designed to 5kPa pedestrian loading with HDG (hot-dip galvanised) steel balustrade panels, cycle rail, and FRP mini-mesh decking.
Manufactured by Outside Products with factory assembly, transported by three semi-trailers, and craned into position.
Moodie Outdoor Products has recently completed the installation of 3 Pedestrian Bridges that were required to link up concrete paths at Sanctuary Point, NSW in a severe coastal environment.
Lengths varied between 7 & 9m’s and were all 2.5m’s long with clear width of 2.2m’s between cycle rails. Due to being severe coastal selection of materials was crucial to provide a durable low maintenance solution. The bridges were constructed using the following:
If you have a similar project in mind and would like to find out more please Contact Us today.
Moodie Outdoor Products has recently completed the supply and installation of a Mawson Pedestrian Bridge at Hunts Creek in North Rocks, NSW.
The bridge is 12.6m long with 2m clear width between handrails. Geotechnical reports were undertaken and the bridge was designed with non-collapsible balustrades as per flood reports.
The bridge is designed to 5kPA pedestrian loading with HDG steel balustrade panels with 20mm CHS vertical balusters at 125mm centres. Hardwood capping rail. Hot dipped galvanised steel construction including joists.
If you have a project that requires a similar pedestrian bridge and would like to find out more please Contact Us today.
Moodie Outdoor Products recently completed the supply and installation of a small Pedestrian Bridge in the rain forest bird aviary at Taronga Park Zoo. The existing timber bridge was dilapidated and slippery as it was in the rain forest environment.
The 3.2m long x 2.1m wide timber bridge was replaced with Roocycle ET structure and handrail with Roocycle EN 150×50 decking boards treated with Traction Sealer to achieve P5 slip rating. Also installed was the stainless steel cable balustrade.
If you have a similar project and would like to find out more please Contact Us today.
Moodie Outdoor Products has recently completed the installation of the Emerald Hills Stage 2 Pedestrian Bridge. This was a design and construct project.
The bridge itself is 22m long and 2.8m wide. It features galvanised steel posts, bearers and cycle rails. Joists are Fibreglass Reinforced Plastic. Decking and handrail posts are Roocycle ET. Balustrading is powdercoated black with Corten steel infill panels featuring the Emerald Hills logo.
The end result looks great and will provide many years of service. If you have a similar project that you would like to discuss please Contact Us today.